null

Matek H743 WING

Was: €84.90
Now: €77.90
(No reviews yet) Write a Review
SKU:
MTK_H743_W
Availability:
Usually shipped in 24 hrs
Shipping:
Calculated at Checkout

The H743 WING by Mateksys is the ultimate Flight Controller for wings and planes. Ultra-powerful H748VIT6 480 MHz processor, 1MB RAM, dual g-sensor, 3x BECs, 13 PWM (S1 to S10 support DSHOT!) and all of what made its predecessors great guarantee unparalleled performances even for advanced projects!

Optimized for ArduPilot, supporting INAV soon and fully loaded with all of any wing pilot may desir!

 

farins-frames-h743-wing-01.jpg 

 

FC Specifications

  • MCU: STM32H743VIT6, 480MHz , 1MB RAM, 2MB Flash
  • IMU: MPU6000 (SPI1) & ICM20602 (SPI4)
  • Baro: Infineon DPS310 (I2C2)
  • OSD: AT7456E (SPI2)
  • Blackbox: MicroSD card slot (SDIO)
  • 7x Uarts (1,2,3,4,6,7,8) with built-in inversion.
  • 13x PWM outputs(including “LED” pad)
  • 2x I2C
  • 1x CAN
  • 6x ADC (VBAT, Current, RSSI, Analog AirSpeed, VB2, CU2)
  • 3x LEDs for FC STATUS (Blue, Red) and 3.3V indicator(Red)
  • 1x SPI3 breakout
  • USB/Beep Extender with Type-C(USB2.0)
  • Dual Camera Inputs switch
  • 5V/9V(12V) for Camera/VTX power switch
  • High-precision Current Sense
  • ADC VB2 voltage divider: 1K:10K
  • ADC AirSpeed voltage divider: 10K:10K
  • INAV TR/SA VTX control: Yes
  • Beeper : Yes
  • RSSI: Yes
  • Analog Airspeed sensor: Yes
  • Digital Airspeed sensor: Yes
  • Static power 160mA@5V

FC Firmware

  • ArduPilot(ChiBiOS): MATEKH743
  • INAV: MATEKH743 (To be supported soon)
  • BetaFlight: MATEKH743

PDB

  • Input voltage range: 9~36V (3~8S LiPo) w/TVS protection
  • 2x ESC power pads
  • Battery Voltage Sensor: 1:10 (Scale 1100 in INAV,  BATT_VOLT_MULT 11.0 in ArduPilot)
  • Current Senor: 132A,  3.3V ADC  (Scale 250 in INAV,  40 A/V in ArduPilot)
  • Sense resistor: 60A continuous, 132A burst.

BEC 5V output

  • Designed for Flight controller, Receiver, OSD, Camera, Buzzer, 2812 LED_Strip, Buzzer, GPS module, AirSpeed
  • Continuous current: 2 Amps, Max.3A

BEC 9V /12V output

  • Designed for Video Transmitter, Camera, Gimbal ect.
  • Continuous current: 2 Amps, Max.3A
  • 12V option with Jumper pad

BEC Vx output

  • Designed for Servos
  • Voltage adjustable, 5V Default, 6V or 7.2V via jumper
  • Continuous current: 8 Amps, Max.10A

BEC 3.3V output

  • Linear Regulator
  • Continuous current: 200mA

Physical

  • Mounting: 30.5 x 30.5mm, Φ4mm with Grommets Φ3mm
  • Dimensions: 54 x 36 x 13 mm
  • Weight: 30g with USB extender

Including

  • 1x H743-WING
  • 1x USB(Type-C)/Beep (Passive buzzer) Extender
  • 1x 20cm SH-4P to GH-4P cable for CAN port
  • 1x 20cm SH-6P to SH-6P cable for USB extender.
  • Dupont 2.54 pins  (Board is shipped unsoldered)